RS-232C, no parity, 8 data, 1 stop bit, 9600 baud

Communication format STX (02h) Command (3Byte) ETX (03h) One command per communication.

Return value Acknowledge ACK (06h) or Not Acknowledge NAK (15h)

Operations with only one command, Video 1, Video2, Panel, and Camera Iris have to be combined somehow with the Common adjustment controls. Could be the single command values switch to the specific commands on those menus, then the common Up, Down etc controls act on them?

If that's the case then the common control buttons will need to be duplicated on each tab for those controls, or perhaps a fixed section of the GUI with those buttons. Greying them out when the Normal, Mode, Language and all Camera operations *except* Iris are in use would be a good thing.

The commands to be used with the Common adjustments, radio buttons? Commands with their own up/down, on/off etc should be normal buttons.

Command list

Normal Command

PON	PowerON		Power ON
POF	PowerOFF	Power OFF
IN0	INput-0		Camera
IN1	INput-1		RGB 1
IN2	INput-2		RGB 2
IN3	INput-3		Video 1
IN4	INput-4		Video 2
VUP	Vol-UP		Volume UP
VDW	Vol-DoWn	Volume DOWN
MON	MuteON		All Mute ON
MOF	MuteOFf		All Mute OFF
AON	AudioON		Audio Mute ON
AOF	AudioOFf	Audio Mute OFF
DON	DisplayON	Display Condition ON (For OSD?)
DOF	DisplayOFf	Display Condition OFF
FON	FreezeON	Freeze ON
FOF	FreezeOFf	Freeze OFF
RUP	ResizeUP	Resize UP
RDW	ResizeDoWn	Resize DOWN
RS0	ReSize0		Resize Reset
PO0	POsition0	Position Reset
PO1	POsition1	Move UP
PO2	POsition2	Move DOWN
PO3	POsition3	Move LEFT
PO4	POsition4	Move RIGHT

Common Adjustment

ALF	Adj-LeFt	Adjusts Value Down
ARG	Adj-RiGht	Adjust Value Up
DSV	DataSaVe	Save Adjust Value
DRS	DataReSet	Reset to default

Video 1 Adjustment

VCN	Video-CoNtrast	Adjust contrast balance
VBR	Video-BRight	Adjust brightness balance
VCL	Video-CoLor	Adjust color balance
VTN	Video-TiNt	Adjust tint balance
VSH	VideopSHarp	Adjust sharpness balance

Video 2 adjustment

VLR	Video-Level-Red
VLG	Video-Level-Green
VLB	Video-Level-Blue

Panel adjustment

PVP	Panel-V-Pos	Adjust vertical position
PHP	Panel-H-Pos	Adjust horizontal position
PPH	Panel-PHase	Adjust sample phase
PCK	Panel-ClocK	Adjust sample clock

Mode adjustment

MO0	Mode-Osd0	OSD mute off
MO1	Mode-Osd1	OSD mute on
MC0	Mode-Ceil0	Ceiling mounted off
MC1	Mode-Ceil1	Ceiling mounted on, flips image upside down, may be disabled in models with document camera, need to test on my TLP-771
MR0	Mode-Rear0	Rear mounted off
MR1	Mode-Rear1	Rear mounted on, flips image left to right for rear projection screen

Language adjustment

LEN	Lang. ENglish
LJP	Lang. JaPanese
LFR	Lang. FRench
LGR	Lang. GeRman
LSP	Lang. SPanish
LIT	Lang. ITalian

Camera adjustment

CZU	Cam-ZoomUp	Zoom wide
CZD	Cam-ZoomDown	Zoom tele
CFU	Cam-FocusUp	Focus far
CFD	Cam-FocusDown	Focus near
CIR	Cam-IRis	Adjust camera iris